SpineNevada in 2006 was the first spine center in the State of Nevada to become authorized and trained to perform artificial disc surgery. Surgeons must complete specific training to perform artificial disc procedures. SpineNevada has experience with over 300 arthroplasties performed using various devices including Bryan, Prestige, ProDisc C, PCM, NUBAC and NeoDisc. The surgeons at SpineNevada instruct other surgeons throughout North America on how to implant devices. Additionally, they also aid in the development of second and third generation devices.
Perhaps the most anticipated advance in spine surgery over the past 20 years was the arrival of the artificial disc. The first artificial disc in the United States received formal approval by the Food and Drug Administration (FDA) for widespread use in the United States on October 26, 2004. While this technology is somewhat new to the U.S., artificial discs have been in use in Europe for more than 15 years.
It is important to remember that this technology is still evolving with new implants continually in development. Your spine surgeon is the best resource to discuss if it is appropriate for you, and what model of artificial disc is best suited for your case.
For example, there are about three models of artificial discs approved by the FDA for use in the United States — Charite, Prestige and ProDisc — and that number is expected to grow as new models emerge on the scene and surgeons become trained in their use. Each disc is designed for use either in the low back (lumbar area) or neck (cervical area).
In addition, other artificial disc models are available on a limited basis through “clinical trials” where a patient agrees to be part of clinical study designed to measure the success of a new disc model, which will be part of an FDA study. Patients who participate in a clinical trial can gain access to the most current technology, even though it has yet to gain FDA approval for use in the U.S.
The artificial disc concept is intended to be an alternative for spinal fusion surgery. Each year in the U.S., more than 200,000 spinal fusion surgeries are performed to relieve excruciating pain caused by damaged discs in the low back and neck areas.
During a fusion procedure, the damaged disc is typically replaced with bone from a patient’s hip or from a bone bank. Fusion surgery causes two vertebrae to become locked in place, putting additional stress on discs above and below the fusion site, which restricts movement and can lead to further disc herniation with the discs above and below the degenerated disc. An artificial disc replacement is intended to duplicate the function level of a normal, healthy disc and retain motion in the spine.
When a natural disc herniates or becomes badly degenerated, it loses its shock-absorbing ability, which can narrow the space between vertebrae. In fusion surgery, the damaged disc isn’t repaired but rather is removed and replaced with bone that restores the space between the vertebrae. However, this bone locks the vertebrae into place, which can then damage other discs above and below.
A common aspect of all artificial discs is that they are designed to retain the natural movement in the spine by duplicating the rotational function of the discs Mother Nature gave us at birth. Most artificial disc designs have plates that attach to the vertebrae and a rotational component that fits between these fixation plates. These components are typically designed to withstand stress and rotational forces over long periods of time. Still, like any manmade material, they can be affected by wear and tear.
Some of the main benefits of the artificial disc parallel that of knee replacement and hip replacement. This can include the following benefits:
Because of the weight of the body and the rotational stress that the trunk places on discs in the low back (lumbar) area, more stress is placed on artificial discs in the lumbar area than in the neck (cervical) area, which only supports the weight of the head.
A second issue relates to the ease of the artificial disc surgery and any necessary revision surgery to replace a worn out artificial disc. Because the surgeon must access the front of the spine, an incision is made in the abdomen for lumbar discs and in the front of the neck for cervical discs. Generally speaking, many spine surgeons believe access to the cervical discs can be easier than the lumbar discs.
When treating knee and hip replacement patients, orthopedic surgeons try to postpone the implantation of an artificial joint until a patient is at least 50 years old so that they do not outlive their artificial joint, which typically lasts anywhere from 15 to 20 years. Revision surgery, which may be necessary to replace a worn-out artificial joint, can be complex.
This is also a concern with the artificial disc. Unlike knee and hip replacement patients who are typically in their 50s or 60s, many patients can benefit from artificial disc technology at a much younger age — in their 20s or 30s. Therefore, the implantation of an artificial disc in younger patients can raise a surgeon’s concern about the potential life span of the artificial disc in the spine and the need for revision surgery to replace a worn-out artificial disc, which can be complex.
The PRESTIGE® cervical disc by Medtronic, www.prestigedisc.com, shown below, includes screws that attach to the vertebral body, and a center plate that retains the movement of the spine.
In summary, some spine surgeons may be cautious about the use of artificial discs for the following reasons:
Generally, the technology is very promising. Your spine surgeon can provide information if your problem can be addressed with this technology.
Due to the fact that the surgeon must access the front of the spine, an incision is made in the abdomen for lumbar discs and in the front of the neck for cervical discs. Typically, access to the cervical discs can be easier than the lumbar discs.
Are you a candidate for artificial disc surgery? This can be a complicated assessment based on the type of disc problem you have. Keep in mind that the physician you choose for spine surgery will have great impact on your outcome from spine surgery - especially artificial disc surgery. The more experienced and trained the surgeon is in spine, the more options you have to explore.
For example, Dr. James Lynch at SpineNevada, has multiple spine fellowships (the highest level of medical training available), including training at the Mayo Clinic.
To receive additional information about artificial disc surgery at SpineNevada Click here.
About Spine Nevada | Biographies: Meet Dr. James Lynch, Spine Neurosurgeon | Meet Nonsurgical Spine Providers | Spine Center | Patient Success Stories | Patient Testimonials | Clinical Outcomes for Spine | In the News | Privacy Notice | Anatomy Library | Exercise Library | Medical Animations | Prevention of Back Pain and Neck Pain | Pain Relief | Symptoms Chart for Spine | Educational Resources | How to Lift | For Physicians | Spine Problems: Back Pain | Neck Pain | Disc Problems: Herniated Disc | Degenerative Disc | Stenosis | Bone Spur | Spondylolysis | Spinal Tumors | Nonsurgical Spine Treatment | Spine Physical Therapy | Spine Surgery | Minimally Invasive Spine Surgery | Tour the Nevada Spine Center | Driving directions to Reno, NV office | Driving Directions to Sparks, NV office | Patient Forms
The pictures displayed in www.spinenevada.com are images of actual patients and employees who have consented to have their picture in this website.